ADVANCED RIGGING (Rigging/Lifting for Supervisor)

Silabus Training
ADVANCED RIGGING
(Rigging/Lifting for Supervisor)

TRAINING INTRODUCTION :
Lifting Supervisor is in charge of the initial work of erecting the load and to ensure that all rigging work is carried out in a safe and efficient manner, adhering to the regulation and to sound established customs and practices. The first consideration must at all times, be directed toward the safeguarding life and limb. This consideration must extend to all persons in vicinity or likely to enter the vicinity.

TRAINING OBJECTIVE :
At the end of course, the participant should be able to:
1. Observe general safety first rules and carry out his duties in a safe and responsible manner
2. Have knowledge of safe working load of the crane he is working with.
3. Have a full knowledge of hand signal (Australian/New Zealand Standard)
4. Understand the correct type of sling, hook shackle etc. for load.
5. Have knowledge of the use of lifting beams, slings and chains
6. Understand the effect of doubling crane hoist rope on safe working
7. Understand use of rope, chain and shackle
8. Understand not to use damaged wire rope or fiber rope, slings or chain where the links are not free or kinked wire rope
9. Understand when slinging a load, pack between sling and load at all point where load has sharp corners, so as to prevent damage to sling
10. Design and apply the knowledge of lifting and lifting plan in their daily Work

TRAINING MATERIAL OUTINE :
1. Introduction
Definition of Dogger, Slinging & Crane Operator
2. Roles & Responsibilities of Rigger
• Rigger Certification System
• Roles & responsibility of Crane Operator
• Roles & Responsibility of Dogger
• Roles & Responsibility of Slinger
• Roles & Responsibility of Traffic Controller / Flagman
• Roles & Responsibility of Lifting Supervisor
• Accident & Prevention
3. Hazard And General Safety
• Outriggers and Crane Stability
• Comparative Soil Bearing Capacities
• Crane Selection Guide
4. Signalling And Communication
• Two way Radios
• Conventional Radio
• Trunked Radio
• Radio Direction for Crane Driver
• Bell or Whistle Code
• Hand Signal
5. Rigging Engineering Calculation
a. Determination on Centre of Gravity
o Rectangular Object
o Round or Oval Shape
o Multiple Load / Object
b. Calculation of Mass
Basic Mass Calculation for Various Shapes of Loads Normally Engaged During Crane Operation versus volume
o Concrete / Cement
o Steel (Mild / Hard
o Liquid (Water)
o Wood
o Sand, etc
** Guidelines for Steel pipe, steel bar, Angle Bar, Mild Steel Plate, Mild steel plate bar, C-Channel, Universal Beams, Universal Columns, etc
c. Lifting Appliances
o Selection on Sling material
 Sling wire FSWR 1570
 Sling wire FSWR 1770
 Chain Sling GT80 / G100
 Synthetic Webbing (Flat/Round Slings)
o Stacking and Clearances
 Clearance
 Stacking Steel Plate
 Stacking Rolled Steel Coils And Other Round Loads
 Stacking Timber
 Care, Maintenance, and Inspection on Sling Material
 Spreader Bar vs Stabilizer Bar
 Use of Slings / Hoists And Tag line
 Determination of S.W.L (SWL versus WLL)
 Minimum Breaking Force (MBF) and its usages
d. Safety Factor Requirements Lifting Material & Human
o Sling wire FSWR 1570
o Sling wire FSWR 1770
o Chain Sling GT80 / G100
o Synthetic Webbing (Flat/Round Slings)

Choke / Hitch Factor
o Rectangular Load
o Round Load
Sling Angles Factor
o Sudut 30o
o Sudut 45o
o Sudut 60o
o Sudut 90o
o Sudut 120o
e. Determination of sling Strength based on diameter & Safety Factor
o Sling Wire
o Synthetic Sling
o Chain Sling
f. Determination of Sling length and lifting angle
g. Inspection of Slings & shackles and attachments
o Sling Wire (5%)
o Chain Sling (5%)
o Synthetic Sling
Note: Determination of acceptance condition of slings and attachments. (Category 1 and Category 2)
h. Calculation of Multiple Sling
o SWL Sling 1
o SWL Sling 2
i. Multiple Crane Lifting / Multiple @ Large Loads
o Tendem Lifting
o Crane Selection and Ordering crane
o Crane type vs Load Chart & Working Radius
• Mobile Crane
• Crawler Crane
6. Role & Responsibility of Lifting Supervisor
Designing Lifting Plan
Special Lifting (Professional Engineer Interferences): Lifting Specialist in General
7. Practical session on:
a. Determination of COG
b. Determination of Volume & Mass
c. Selection of slings
d. Lifting Techniques
e. Hand Signaling & Radio Communication
f. Inspection of Crane & Lifting Hoist appliances
g. Manual Lifting & Mechanical
h. Lifting Gin Wheel Application & Limitations

NOTE : Peserta melengkapi laptop dengan software AutoCAD dan Inventor.

VENUE : Jakarta (Maxone Hotel Menteng, Balairung Hotel Matraman, Sentral Hotel, Haris Tebet, Gd Muamalat Institute, Ibis Manggadua, Little Amaroossa Residence, Cosmo Amaroossa, Zodiak MT. Haryono, Grand Tjokro)

TRAINING DURATION : 3 (Tiga) Days

TRAINING TIME :

INVESTMENT PRICE/PERSON :
1.Rp. 6.500.000/person (full fare) or
2.Rp. 6.250.000/person (early bird, payment 1 week before training) or
3.Rp. 5.950.000/person (if there are 3 persons or more from the same company)

FACILITIES FOR PARTICIPANTS:
1.Training Module
2.Flash Disk contains training material
3.Certificate
4.Stationeries: NoteBook and Ballpoint
5.T-Shirt
6.Backpack
7.Training Photo
8.Training room with Full AC facilities and multimedia
9.Lunch and twice coffeebreak every day of training
10.Qualified Instructor